INSTRUCTIONS PERTAINING TO A RISK OF FIRE,OR INJURY TO
PERSONS
IMPORTANT SAFETY INSTRUCTIONS
Lighted lamp is HOT!
WARNING — To reduce the risk of FIRE OR INJURY TO PERSONS.
1) Turn off / unplug and allow to cool before replacing lamp.
2) Lamp gets HOT quickly! Contact only switch / plug when turning on.
3) Do not touch hot lens or cowl.
4) Do not remain in light if skin feels warm. (Light is intense, it may cause
“sunburn”.)
5) Do not look directly at lighted lamp.
6) Keep lamp away from materials that may burn.
7) Useonlywithwattageandlampmarkedonxture.
8) Do not touch the inner glass envelope of the lamp at any time. Use a soft
cloth. Oil from skin may damage lamp.
9) Donotoperatethexturewithadamagedormissinglens.
FOR USE WITH LANDSCAPE LIGHTING SYSTEMS ONLY.
1) The device is accepted as a component of a landscape lighting system
where the suitability of the CSA or UL labeled combination shall be deter
mined by CSA, UL respectively or the local inspection authorities having
jurisdiction.
2) Fixtureshallbeconnectedtoanextralowvoltagetransformerapproved
for use with landscape lighting systems.
3) Thisxtureistobeconnectedtoasecondarywiringofthefollowingtype:
12 GA 60°C minimum type;
SPT-3 suitable for outdoor use; or
approved landscape lighting cable.
Date Issued: 12/2/11 IS-15073-CB
DOM ETRE INSTALLE A L’EXTERIEUR
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page
Pour de plus amples informations sur la garantie, cliquez sur le lien ci-dessous : http://www.landscapelighting.com/portal/warranty_page
QUIC DISC
™
WIRING INSTRUCTIONS
Turn off power.
Thefulllengthofthe18GAxturewiremaybeusedtoconnectwiththe10GAor12GAcableprovidedthefollowingconditionsaremet:
•Wiringistobeprotectedbyroutingclosetothextureoraccessoryorsecuredtoabuildingstructuresuchashouseordeck.
• 18GAxturewiringistobecutoffsothatitisattachedtotheconnectorwithin6inchesofthextureorbuildingstructure.
• Ifitisnecessarytomaketheconnectionsunderground,thennomorethan6inchesofthe18GAxturewireistobeburied.
The Quic Disc
™
connector is designed to install onextureandaccommodatesone18GAxturewireandone 10 GA or one 12 GA supply wire.
Place the 10 gauge supply wire across the area marked 10 GA on Quic Disc
™
or place the 12 gauge supply wire across the area marked 12 GA
on Quic Disc
™
.
Placethe18gaugexturewireacrosstheareamarked18GAontheQuicDisc
™
. After the wires are in place, connecta the top of the Quic
Disc
™
tothebasewithsuppliedscrew,makingsurethatthewiresremainatinthebottomportionoftheQuicDisc
™
, and the screw is tightened
all the way down.
Thecoppercontactswillautomaticallypiercethewires’insulation.Excess18GAxturewirethatsticksouttheendoftheQuicDisc
™
is to be cut off.
Makenootherwiringconnectionstothe18GAxturewire.
SAVE THESE INSTRUCTIONS
INSTALLATION AND ASSEMBLY
Before Starting:
A)Desiredlocationforeachxtureshouldbedeterminedbefore
construction of wall is started.
B)Ifaccesstobackofwallislimited,cable/conduitshouldberunpriorto
construction.
1) TURNOFFPOWER.
2) Assemble brackets to bottom of housing using washers and screws.
3) Knock off corner of brick on either side or below housing for cable/conduit
entryandexit.
4) Screw supplied 1/2 NPT plugs into holes in housing not being used for
wire passage.
5) Remove socket bracket from inside of housing.
6) Mortarhousingintoplacenotingthefollowingitems:
A) Supply wire may need to be run into housing at this time, if so pull supply
wire through appropriate hole in housing and secure cable/conduit to
housing using a suitable connector.
B) Embed lower brackets in mortar.
C) Mortar housing into place as it if were a brick.
D) Allow mortar to cure before wiring and re-assembling brick light.
7) Continuebuildingwall,installingremaininghousingasspeciedabove.
NOTE: Before the coarse of brick over housing is laid, attach brackets to top
of housing using washers and screws.
CAUTION:Whensecuringbrackets,donotapplyalotofpressureor
force. This may damage uncured mortar.
8) Allow wall to cure.
9) Makewireconnections(connectorsnotprovided.)Thisxtureusesa
non-polarizedsocket.Eachsupplywiremaybeconnectedtoeitherxture
wire.
10) Push socket bracket into housing and secure in place with screws.
11) Insertrecommendedlamps.
12) Assemble cover/lens to housing.
WASHER
RONDELLE
SCREW
VIS
COVER/LENS
COUVERCLE/DIFFUSEUR
BRACKET
SUPPORT
SCREW
VIS
SOCKET BRACKET
PATTE DE SUPPORT
DELADOUILLE
HOUSING
BOLTIER
Kommentare zu diesen Handbüchern