Kichler 15745 Bedienungsanleitung PDF herunterladen

Kichler

Design Pro LED

Hardscape Fixture Installation Instructions

P/N: 15745AZT/BBR/CO, 15746AZT/BBR/CO, 15756AZT/BBR/CO

Dev. No: CP300289AZT/BBR/CO, CP300347AZT/BBR/CO, CP300348AZT/BBR/CO

READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION

KEEP THESE INSTRUCTIONS

This ﬁxture is intended for installation in accordance with the National Electric Code (NEC) and Local code speciﬁcations. Failure to adhere to

these codes and instructions may result in serious injury and/or property damage and will void the warranty.

1) WARNING: This ﬁxture is not to be installed within 10 feet (3M) of a pool, spa, or fountain.

2) This ﬁxture is to be used only with a power unit (transformer) rated a maximum of 300 W (25 AMPS) 15 volts.

3) The 18AWG ﬁxture wire is not intended for direct burial.

4) Direct burial rated wire is to be buried a minimum of 6” (152mm) beneath the surface of the ground. NOTE: If additional Direct Burial wire is needed,

contact your local Kichler

landscape distributor.

  • 8GAwirecanbepurchasedinlengthof250’(76M),15503-BK.

  • 10GAwirecanbepurchasedinlengthof250’(76M),15504-BK.

  • 12GAwirecanbepurchasedinlengthsof100’(30M),15501-BK;250’(76M),15502-BK;500’(152M),15505-BK;and1000’(304M),

   15506-BK.

5) DO NOT INSTALL in walls where the capstones overhang the wall less than 3/4” [19 mm]

6) Wiringconnectionsmustbemadewithapproved/listedwireconnectiondevice(s)suitablefortheapplication.Donotexceedmanufacturers’wiring

combination speciﬁcations for size and quantity of conductors.

INSTALLATION OF 15745, 15746, or 15756 IN BRICK or MASONRY WALL

(SEE FIG. A)

1) Turn off power.

2) Determine the desired location for each ﬁxture before construction of wall is started.

3) Insert stainless steel mounting plate in between layers of hardscape material. The use of adhesive or mortar (not provided) to secure the ﬁxture in

place is optional.

4) Route the ﬁxture wire through the wall to the main low voltage supply cable using standard masonry procedures. A “V” shaped notch can be cut into

the hardscape material to aide in wire management if desired.

5) Attach ﬁxture to bracket using screws provided.

6) Connect ﬁxture wires to main low voltage supply cable using the connector(s) provided.

FIG. A

Date Issued: 6/25/10 IS-15745-CB

WARRANTY

WE WARRANT THE LANDSCAPE PRODUCTS FEATURED IN OUR LANDSCAPE LIGHTING CATALOG (WITH THE EXCEPTION OF LIGHT BULBS) FOR FIVE YEARS AGAINST

DEFECTS IN MATERIALS AND WORKMANSHIP IF IT WAS PROPERLY INSTALLED AND FAILED UNDER NORMAL OPERATING CONDITIONS, PROVIDED IT IS RETURNED TO

THE POINT OF PURCHASE, WHERE IT WILL BE REPAIRED OR, AS IT MAY BE DETERMINED, TO REPLACE THE LANDSCAPE PRODUCT OR PARTS USED ON THAT PRODUCT.

QUIC DISC

™

WIRING INSTRUCTIONS

Turn off power.

The full length of the 18 GA ﬁxture wire may be used to connect with the 10 GA or 12 GA cable provided the following conditions are

met:

•Wiringistobeprotectedbyroutingclosetothextureoraccessoryorsecuredtoabuildingstructuresuchashouseordeck.

• 18GAxturewiringistobecutoffsothatitisattachedtotheconnectorwithin6inchesofthextureorbuildingstructure.

• Ifitisnecessarytomaketheconnectionsunderground,thennomorethan6inchesofthe18GAxturewireistobeburied.

The Quic Disc

™

connector is designed to install one ﬁxture and accommodates one 18 GA ﬁxture wire and one 10 GA or one 12 GA

supply wire.

Place the 10 gauge supply wire across the area marked 10 GA on Quic Disc

™

or place the 12 gauge supply wire across the area

marked 12 GA on Quic Disc

™

Place the 18 gauge ﬁxture wire across the area marked 18 GA on the Quic Disc

™

. After the wires are in place, connecta the top of the

Quic Disc

™

to the base with supplied screw, making sure that the wires remain ﬂat in the bottom portion of the Quic Disc

™

, and the

screw is tightened all the way down.

Thecoppercontactswillautomaticallypiercethewires’insulation.Excess18GAxturewirethatsticksouttheendoftheQuicDisc

™

is to be cut off.

Make no other wiring connections to the 18 GA ﬁxture wire.

OUTDOOR USE ONLY

DOM ETRE INSTALLE A L’EXTERIEUR

INSTRUCTIONS

For Assembling and Installing Fixtures in Canada

Pour L’assemblage et L’installation Au Canada

1 2

Inhaltsverzeichnis

Seite 1 - Design Pro LED

Kichler® Design Pro LED Hardscape Fixture Installation InstructionsP/N: 15745AZT/BBR/CO, 15746AZT/BBR/CO, 15756AZT/BBR/CO Dev. No: CP300289AZT/BBR/CO,

Seite 2 - Kichler® Design Pro DEL

Kichler® Design Pro DELInstructions de montage pour luminaire d’aménagement paysager en matériaux inertesP/N : 15745AZT/BBR/CO, 15746AZT/BBR/CO, 15756